r58p8x3P.bin:
	R58 v3_P BEc 08.02.2003 P8E/P8N S8B/S8C/S8D CU53xx/CU58AF

[GPS-demo] jaapotijaap ja höpö

3P:ssä normaalimoden muutoksia:
skannauksen nopeutus ja pari verenpainetta laskevaa mykistystoimintaa.

SC:SLrate = msec ja SC:SL_qsy = kHz

	Kun taajuus vaihtuu vähemmän kuin SL_qsy, askellusviive on vanha
	SC:rate=msec. Kun se vaihtuu enemmän kuin SL_qsy, askellusviive
	on SC:SLrate=msec. Sopivia arvoja voisivat olla
	rate=10msec, SLrate=60msec ja SL_qsy=100kHz.

b*:AutorJ = on/oFF

	Jos listen-limitti ylittyy, taajuus rejektoituu itsestään. Järkevä
	käyttö edellyttää että myös unrejt on annettu. Siis jos tulee yli
	X sekuntia signaalia, on taajuus rejektissä Y minuuttia.
	Sopinee parhaiten repiitteri-viipaleen yhteyteen (default b2)

GE:rEPSit = seconds

	Repeater Sitter's Special.
	Joko nolla (ei toiminnassa) tai 1..255 sekuntia. Luurin ollessa pitimessä
	audio katkeaa itsestään näin monen sekunnin jälkeen, aueten taas seuraavalla
	overilla. Nostettu luuri pitää audion auki normaalisti.

dH:GPS H

	256 viimeisintä GPS:n puhumaa merkkiä (tinataan SIO-A RXD:hen).
	Keskeneräinen.



Vanhempia muutoksia 3J:n jälkeen:

!! 3.J 020409 If id_bye == "", tx unnecessary.
!!            PA_Hot and ant_bad messages as strings in setup,
!!              no fixed usage (though very suggestive names).
!!            Repeater USEcnt open counter.
!!            Repeater USEhrS transmitter hours.
!!            Repeater blip is pre-empted by carrier.
!!            Repeater (re-)enters open state when /LOCAL pin rises,
!!             useful for triggering cwid externally.
!!            Repeater gives better S-reports (setup S1rSSi, S9rSSi),
!!             rssi below s1rSSi = 1, rssi above S9rSSi = 9.
!!            6.25kHz step hidden.
!!            Power relay is toggled with delay when battery dries,
!!             relay stays in On position with bench supply,
!!             Lo_batt shown in LCD,
!!             If voltage rises back over 10 volts,
!!             lo_batt ends and normal operation resumes.
!!            Powering up powerbutton in off-position, the livelock removed.
!!            CCIR CALL also rings bell.
!!            FSK modem is re-enabled every hour (unstuck).
!!            Repeater CTCSS access method, input EXIN2, polarity selectable
!!             with rP:CtCPol = POS/nEG, configured with rP:ACCESS = CtCSS.
!!            CTCSS freq and channel step are kept separately in memories.
!!            CTCSS tx indicator is the little mast icon.
!!            GE:onHook/oFFHook scripts. REMEMBER to clear them from setup.
!!            Command input fixed to understand either 0xC or 'C' for CL.
!!            Little button just aborts scanner, if scanning.
!!        XXX halfway with mute operation.
!!            onHook-script can execute 'T' -> selkun Taakse. any key,
!!             hook or alarm bell clears the mute (no re-triggers here).
!!            Mute (Selective) indicator is the little key icon.
!!            Repeater CCIR commands like DTMF commands, using prefix
!!             from rP:ccirPF, for example when prefix is "1234"
!!             ccir 1234 = dtmf ##, 12340 = #0, 12341 = #1 and 12349 = #9.
!!             multidigit commands are not (yet) understood.
!!            Temporary rejects now max 20, parameter rJ:n_tEmP can trim
!!             the lifo length into 1...20 (0=20)
!!            APRS transmit aux ptt from /LOCAL. Quick qsy into other freq,
!!             tx while /LOCAL is low and qsy back to original frequency.
!!             Settings are GE:APrS=off/on and tr:trAPrS=kHz
!!            APRS /PTT sense was wrong.
!!            Scanner 'carrier wait' lingering parameters b*:SCtAIL
!!             now presented in seconds.
!!            Repeater 'hog' message now configureable.
!!            Scanner b*:SCLIStEn value 255 means now 'infinite patience'.
!!
!!            Setup checklist:
!!                 b*:SCtAIL   unit is now seconds
!!                 GE:onHoo    clear this
!!                 GE:oFFHoo   clear this
!!
!! 3.L 020523 Sq:BonGo Hz for local blip from closing squelch.
!!            Key blip and serv blip setting 0 -> no corresponding blip.
!!            dF:EntLen safety for entering setup.
!!     020527 Memory uses the corresponding b?-band, setting band_xxx
!!             variables ok.
!!            Also CTCSS updates in setup use the mem- or the vfo-variable
!!             as needed.
!!     AL3    EXAL changeable from keypad, fsk, dtmf and ccir.
!!             GE:GPio1 has the control on/off state;
!!             io:ctl 1c and io:ctl 1d are command prefixes to set it
!!             from ccir and dtmf, respectively.
!!            warm boot thru setup (dF:reboot).
!!            repeater suspension (rP:SUSP*).
!!            display "CALL" runs also a HH:MM:SS counter.
!!            rP:HidE_9 pass/hide to block abuse of #9 command.
!!     AL4    repeater_TBLIP cSEC counter.
!! 3.N 020703 Hide9 bug fixed (when hidden, #9 tightened squelch instead).
!!            Longstanding bug in piob_mode fixed, overwritten by _bss bzero.
!!     030109 rP:SInPLE on/oFF flag for wierd simplex mode of repeater.
!!              this disables rx during repeater tx.
!! 3.P 030129 quick/slow qsy in scanner.
!!     030129 oops, forgot defaults of the new qsy-parameters.
!!            autoreject.
!!            repeater sitter's special.